Manitou Roto telehandler (MRT) rental: one machine for lifting, crane work and work at height
When you rent a Manitou roto telehandler, you get a forklift, a crane and an aerial work platform in one machine: the superstructure of the MRT series rotates through 360 degrees while the chassis stays in one place on its outriggers. Luibl Rental has ten MRT models in its rental fleet, with 4,000 to 7,000 kg load capacity and 17.90 to 34.70 m lift height.
On confined sites, every repositioning of a fixed telehandler costs time: retract the outriggers, manoeuvre, realign, set up again. On facades, halls and high-rise buildings with many load points, this adds up over the day. A roto telehandler serves the full circle around the machine from a single position. With the right attachment, it also takes on tasks that would otherwise require a mobile crane or a separate aerial work platform.
Ten Manitou MRT models cover 17.90 to 34.70 m lift height
Which Manitou Roto is right depends on the lift height and the load at the most distant placement point. The rated load capacity only applies close to the machine; as outreach increases, the permissible load drops significantly according to the load chart. Choose the model by the least favourable load point, not by the highest load capacity.
Up to 18 m lift height: compact for confined sites and courtyards
- Manitou MRT 1840: 17.90 m lift height, 4,000 kg load capacity, 15.10 m outreach, 2.39 m wide
- Manitou MRT 1845: 18.00 m lift height, 4,500 kg load capacity, 15.20 m outreach
21 to 26 m lift height: the class for building construction and installation
- Manitou MRT 2150 Privilege: 20.60 m lift height, 5,000 kg load capacity, 18.10 m outreach
- Manitou MRT 2260: 21.80 m lift height, 6,000 kg load capacity, 18.20 m outreach
- Manitou MRT 2550 Privilege: 24.70 m lift height, 5,000 kg load capacity, 21.40 m outreach
- Manitou MRT 2570: 24.80 m lift height, 7,000 kg load capacity, 20.50 m outreach
- Manitou MRT 2660: 25.90 m lift height, 6,000 kg load capacity, 21.70 m outreach
30 to 35 m lift height: for tall facades, industry and steel construction
- Manitou MRT 3060: 29.90 m lift height, 6,000 kg load capacity, 25.70 m outreach
- Manitou MRT 3570: 34.70 m lift height, 7,000 kg load capacity, 28.00 m outreach
- Manitou MRT 3570 ES: 34.70 m lift height, 7,000 kg load capacity, 28.00 m outreach
All models are diesel-powered. The full data sheets are on the individual model pages.
Roto or fixed: a Manitou Roto pays off with many load points in a confined space
The Manitou Roto plays to its strengths where a fixed telehandler would have to reposition constantly. For pure material handling on open, level ground, a fixed machine is usually the more economical choice.
- Rotating superstructure: The MRT models slew the load all around the machine. One position covers load points in front of, beside and behind the machine.
- Outriggers: All MRT models have outriggers. They only reach full lift height and outreach when stabilised; this provides stability at great height but costs time with every repositioning.
- Lift height: The MRT series starts at around 18 m and reaches up to 34.70 m. Below that, fixed telehandlers cover most tasks.
- Space requirement: Because the chassis stays put, the Roto needs less manoeuvring space than a fixed machine that has to drive up to every load point.
If you mainly handle pallets on level ground, you will find suitable machines among the fixed Manitou telehandlers. An overview of all Manitou machine types is on the page Manitou telehandlers.
With attachments, the Manitou Roto becomes a crane or an aerial work platform
The roto telehandler changes its job by changing the attachment. Each attachment has its own load chart, which the operator must know before use.
- Fork carriage and pallet forks: lifting material onto floor slabs, scaffolding and roofs or unloading trucks.
- Load hook, winch and crane jib: The MRT works as a mobile crane and places loads over obstacles such as parapets or roof overhangs.
- Work basket: With a basket approved for the model, the Roto becomes an aerial work platform for installation, facade work and maintenance at height.
- Further attachments: We put together buckets and special grabs on request.
Which attachments suit your model is shown in the overview Attachments for telehandlers. Name the attachment you need in your enquiry, and we will plan machine and tool together.
Weight and outriggers decide whether the Manitou Roto suits your site
Depending on the model, a Manitou Roto weighs between 13,300 kg (MRT 1840) and 23,800 kg (MRT 3570). Clarify access, ground conditions and set-up area before you send your enquiry.
- Access: The models are 2.39 to 2.50 m wide and 2.94 to 3.26 m high. Gates, passages and bends on the way to the set-up position must allow for this.
- Ground: The outriggers transfer the load into the ground at specific points. On soft ground, backfill or above basement ceilings, load-spreading pads are needed; if in doubt, a structural engineer decides.
- Set-up area: Allow space for the extended outriggers and the slewing range of the superstructure, and cordon off this area during operation.
- Transport: We organise transport by low-loader from our Passau location throughout the Czech Republic. The low-loader needs a paved area for unloading.
Operators of a Manitou Roto need a qualification matching the rotating machine
Anyone operating a roto telehandler needs more than the basic telehandler qualification. In the Czech Republic, the applicable occupational safety rules (Act No. 309/2006 Coll.) and Government Regulation No. 378/2001 Coll. on the safe operation of machinery are decisive.
- Basic qualification: It qualifies the operator to run a telehandler in forklift mode.
- Qualification for rotating machines: Telehandlers with a rotating superstructure require an operator qualification matching this machine type in line with applicable Czech safety rules and CSN EN standards.
- Qualification for basket and crane operation: Anyone working with a work basket or load hook needs a matching qualification for each of these modes. Personal fall protection equipment is used in the basket in line with Government Regulation No. 362/2005 Coll. (work at height).
- Briefing and appointment: The employer briefs the operator on the specific machine and appoints them to operate it.
Luibl Rental does not offer training itself but informs you about certified providers. More on the Trainings page.
FAQ: Manitou Roto telehandlers

How high does a Manitou Roto telehandler lift?
What is the difference between a Manitou MRT and a fixed Manitou MT?
What qualification do I need for a roto telehandler?
Can a Manitou Roto be used as a crane?
Can a roto telehandler lift people to height?
How does a Manitou Roto get to the site?
Request a Manitou Roto telehandler: with these details we prepare your quote
The more precise your enquiry, the better our model proposal fits. These details help our dispatch team:
- site location and rental period
- required lift height and the heaviest load with its distance from the machine
- attachments, for example work basket, winch or forks
- access and ground conditions at the set-up position
You will promptly receive a quote with model, transport and attachments. Request a Manitou Roto quote now.